EnTech Taiwan EnTech Taiwan
January 21, 2018, 05:44:01 PM *
Welcome, Guest. Please login or register.

Login with username, password and session length
   Home   Help Search Login Register  
Pages: 1 [2] 3 4 ... 10
 on: December 07, 2013, 06:51:43 AM 
Started by name - Last post by name
Well, this error event (id=1000) happens with almost any program (maybe using graphics; but not smp). It shows up especially quickly with flashplayer, but even without fp, eventually slowly worsens causing hangs everywhere.
But here's a definitive trick that stops the error: after starting powerstrip, rename pshook.dll (for example pshook'.dll).
Just remember to rename it back to pshook.dll *before* starting it again in the future, otherwise hotkeys won't work.

 on: November 29, 2013, 01:32:11 PM 
Started by name - Last post by name
checked: now I'm using vlc for youtube. No browser hangings any more

 on: November 27, 2013, 09:38:19 AM 
Started by name - Last post by name
(event viewer, administrative events)

Event Properties - Event 1000, Application Error

+ System

- EventData

   C:\Program Files (x86)\PowerStrip\pshook.dll

It repeats every 10 seconds (average).
I suspect it is the cause of both firefox and googlechrome hanging frequently [haven't checked yet]

 on: August 17, 2013, 08:26:29 AM 
Started by Noceous - Last post by Rik Wang
PowerStrip has not and will not be updated to support Win8, but it does work under the 64-bit edition of Win8.

 on: August 16, 2013, 11:45:50 AM 
Started by Noceous - Last post by Noceous
Does Powerstrip support Win8?

 on: July 21, 2013, 04:16:50 PM 
Started by ThurstonX - Last post by ThurstonX
Thanks for the explanations, Rik.

I'll continue to use PowerStrip happily.  Truly a great app.

 on: July 21, 2013, 03:36:02 PM 
Started by ThurstonX - Last post by Rik Wang
1. If I'm not mistaken the CRU employs an EDID override - its a monitor rather than a GPU utility. The EnTech equivalent would be MonInfo, not PowerStrip.

2. There is no conflict, since one just tells Windows your monitor timing differs from what Sharp says it is, and PowerStrip attempts to directly program the GPU.

3. It depends on whether the EDID override applied by CRU or MonInfo is sufficient or not.

 on: July 19, 2013, 05:33:00 PM 
Started by ThurstonX - Last post by ThurstonX
Just wanted to share my experience in the hope it might help someone down the line.

I had been running a Sapphire 9600XT under Windows 7 32-bit using the driver provided via Windows Update.  As it was under XP, PowerStrip allowed me to get my Aquos to accept 1368x768, and thus run Dot By Dot at the near-native resolution.  The Aquos is a LC-32GA5U circa 2005, and has a DVI input for PCs.

I decided to upgrade the 9600XT and got a used Radeon HD 3850 AGP, as it's supported by PowerStrip.  I had zero luck trying to install the drivers from AMD.  Apparently it's a problem with the 3850's "9515" device ID not being included in the INF.  I ended up using the "ATI Catalyst  12.11 B11 HotFix 5 Pre 8 x32Bit Legacy Driver" from Guru3D.  Works like a champ.  But when I tried to define a custom resolution by pasting in the timings I'd used with the 9600XT, PowerStrip prompted me to restart.  Upon rebooting, the 1368x768 res was not available.  I did uncheck the "Hide modes not supported by this monitor" option, and created a monitor driver with PowerStrip, installing it via the Device Manager.  But whatever I tried, I could not get PowerStrip to use my custom res.

Then I recalled an app by the name of Custom Resolution Utility (CRU).  I used it to define a custom resolution for the Aquos (basically an EDID override, if I understand it correctly).  et voila!  PowerStrip allowed me to use my custom res!  I could then use PowerStrip's Custom Resolution details window to tweak the CRU settings to match.  This setup works without a hitch.


I do have a couple questions:

1) what could be the reason I was unable to use PowerStrip initially with the 3850, esp. in light of the fact that the 9600XT worked fine in the same system?

2) is there any potential conflict between CRU and PowerStrip?  My initial impression is that there is not, but it's only been a day since I got it to work.

3) While I will continue to use PowerStrip, is it possible to use only CRU to achieve the same end?  PowerStrip has a few more advanced features that make it easier to use and tweak (no reboots required when timings are adjusted; the ability to shift the desktop to compensate for the extra pixels).


Thanks for your time. I hope this proves useful to others.

 on: June 29, 2013, 01:25:08 PM 
Started by ThurstonX - Last post by ThurstonX
Thanks for confirming, Rik.

 on: June 29, 2013, 05:33:24 AM 
Started by ThurstonX - Last post by Rik Wang
I'm afraid it is not supported. The GeForce 6 used an NV40 class GPU; your GT 610 uses a GF119 class GPU.

(Yes, the naming of these things is confusing...)

Pages: 1 [2] 3 4 ... 10
Powered by MySQL Powered by PHP Powered by SMF 1.1.15 | SMF © 2006-2008, Simple Machines Valid XHTML 1.0! Valid CSS!